Lengths, areas and counts
Measure by clicking, how each quantity is worked out, and the settings that turn a length into m2 and an area into m3.
Three tools do most of the take-off: Length, Area and Count. A fourth, Dimension, takes a length straight off a dimension written on the drawing.
| Tool | How | Gives | For |
|---|---|---|---|
| Length | Click along the line, then Enter. At least 2 points. | m | Walls, skirting, DPC, drains, kerbs |
| Area | Click the corners in order round the shape, then Enter. At least 3 points; the last corner joins the first by itself. | m2 | Slabs, floors, roofs, paving |
| Count | Click each one once, then Enter. | No. | Sockets, columns, fittings, trees |
| Dimension | Click on a dimension figure written on the drawing. | m | A length taken off its dimension line |
Before pressing Enter, type the description in the box on the bar (it starts as Length, Area or Count); it can be changed later in the table. Undo point (Backspace) takes the last click back.
Clicking accurately
- Snap (on by default, at the foot of the drawing): a click within 8 screen pixels of the end of a drawn line lands exactly on it, marked by a small square. It works on CAD drawings, not on scans.
- Shift, or Straight on a tablet: each point goes straight across or straight down from the one before.
- Zoom in: at 100% one screen pixel is one drawing unit, 35 mm on site at 1:100; at 400% it is about 9 mm.
How the quantities are worked out
- A length is the sum of its straight pieces. A curve is measured as several short straight pieces along it: the more points, the closer to the true curve.
- An area is worked out from its corners in the order clicked (the surveyor's shoelace method). It works for any shape with straight sides, an L or a T, as long as its sides do not cross each other.
- A count is the number of clicks.
The table of measurements
Each measurement is a row, like dimension paper: its number and colour, the description, × (times), the quantity with its unit, and its BoQ item. p.1 shows it on the drawing; the chevron opens its settings; the bin deletes it (and its rows on the measurement sheets).
Under the description HodariQ shows how the quantity was made, e.g. = 25.2 x 3 x 3, and the figure on plan when a pitch or a centre line changed it.
The settings
| Setting | What it does |
|---|---|
| × (times) | How many times it is built: typical floors, identical rooms, houses of one type. Above zero; up to 2 decimals. |
| x Height / depth | A length times a height gives m2 (a wall); an area times a depth gives m3 (a slab, an excavation). |
| Height from section | A height measured on a section instead of typed (see Heights from sections). Shown once the contract has heights. |
| Zone | The floor, block or house it belongs to. |
| Deduct | Taken off its BoQ item: an opening, a void. |
| Roof pitch, centre line of walls | The true length or area up a slope, and walls moved to their centre line (see Roofs and wall centre lines). |
| + Assembly: add its items... | One measurement filling several BoQ items (see Assemblies). |
The quantity is the measured figure x height (when given) x times, rounded to 3 decimals: the same rule as the measurement sheet.
Deductions
A measurement ticked Deduct keeps its positive figure in the table, marked Deduct, and is taken off when it reaches the BoQ: its row on the measurement sheet is negative, and the dimension sheets list it under the deductions.
Dimension
With Dimension on, click a figure written over a dimension line (e.g. 3,660). Its dimension line becomes a length named Dimension 3,660, and HodariQ compares it with the figure: within 1% it says as written; otherwise it warns that the line measures another length at this scale. It is a quick test of the scale and of the drawing. Press Done (Esc) to stop.
Good to know
Length, Area and Dimension need the page's scale; Count does not. A counted door or window has Width (m) and Height (m) instead of a height: its size, used for the deductions from the walls.
Something unclear? Ask us on WhatsApp: we answer the same day.