The screen, keyboard and tablet
What each part of the take-off screen does, the keys that speed it up, and measuring on a tablet.
The take-off fills the screen: the drawing on the left, the panel of measurements on the right, and two rows of buttons above them.
The top row
| Part | What it does |
|---|---|
| Arrow, name, Details | Back; the drawing's form. Under the name: into the BoQ or VO it measures into. |
| Page 1 / 3 and the arrows | Changes page. Each page has its own scale; HodariQ reads it the first time the page opens. |
| Minus, plus, the percentage, the four arrows | Zoom out and in by 25%, from 25% to 600%; the four arrows fit the whole page in the window. A drawing bigger than the window opens fitted; a small one opens at 100%. |
| The scale pill | The scale of this page and how it was found (see The scale). Hover over it for the full message. |
| The zone box | The zone new measurements go into, or + New zone.... |
| Read Scale | Reads the scale from the drawing again and, when it finds one, replaces the scale of the page, even one set by hand. |
| Panel | Hides or shows the panel of measurements: more room for the drawing. |
| New Revision | Uploads the architect's revised drawing and carries the measurements over. |
| Print, Dimension Sheets | The marked drawing and the take-off on dimension paper. Shown once something is measured. |
The tools
The second row, in groups: Scale; Length, Area, Count; Dimension, Measure Height, Height List, Room, All Rooms; Doors & Windows, Same Symbols, Check Dimensions; and at the far right the question-mark icon (raise a query) and the speech-bubbles icon (the list of queries, with the number still open). Length, Area, Dimension, Room and All Rooms need the page's scale first; Count, Scale, the queries, Same Symbols and Measure Height do not.
While a tool is on, a bar under the buttons says what to click next, counts the points, and holds Undo point, Finish (Enter) and Cancel (Esc). Snap, the switch at the foot of the drawing, is always in reach.
The panel
A tool's findings come first (the rooms found, the door marks, the symbols, the dimension checks, the heights, the queries), then Measurements: one row each, numbered and coloured as on the drawing. The colours repeat after ten measurements and are the same on the printed drawing.
Keyboard
| Key | While | Does |
|---|---|---|
| Enter | Length, Area, Count | Finishes the measurement (the same as Finish (Enter)). |
| Enter | Scale, after the two clicks | Sets the scale with the length typed. |
| Enter | A query, after the two corners | Raises the query with the question typed. |
| Esc | Any tool | Cancels it; nothing is saved. |
| Backspace | Length, Area, Count, Scale | Takes the last point off (Undo point). |
| Shift, held while clicking | Length, Area, Scale | The new point goes straight across or straight down from the last one, whichever is nearer. |
| Enter, Esc | Typing a new zone | Adds it, or gives up. |
| Enter | The New drawing window | Start take-off once everything is filled. |
Good to know
The keys do nothing while you are typing in a box (a description, a height): click the drawing first.
On a tablet
- Two fingers zoom: the drawing stretches at once under your fingers, the point between them stays there, and it is drawn sharp again when you lift them.
- One finger scrolls the drawing; a tap is a click.
- There is no Shift key: switch Straight on in the bar while measuring a Length or an Area for straight lines.
- There is no Backspace: use Undo point.
- Panel hides the measurements for more drawing. Held upright, the panel goes under the drawing instead of beside it.
- On a touch screen the buttons, boxes and rows are made bigger, for a finger.
Tip
Zoom in before clicking corners on a tablet: a finger covers more of the drawing than a mouse pointer, and Snap catches a corner only when the tap lands within a few pixels of it.
Something unclear? Ask us on WhatsApp: we answer the same day.